Product family
Point or cable-based detection components for a stated coverage and alarm interface.
Component selection
7 local draft records. Includes unfinished records and Family overviews. Draft · Noindex. Reference configurations are not approved stock. Image public-use review remains separate.
Show content-ready drafts
LCP-000092
A conductive, braided leak-sensing cable documented for liquid-cooling equipment. The manufacturer identifies the MA1YHZ0102(1.0) reference and an operating temperature range of -40…
LCP-000094
A compact spot sensor combining optical and electrode detection, with RS485/MODBUS-RTU output. The documented XW-DC-01A uses a DC 9–30 V supply and…
LCP-000093
A coiled, connector-terminated leak-sensing line for use with a compatible locating controller. The documented XW-ES2-10H1 cable is 6.0 mm in diameter and…
LCP-000096
A DIN-rail-style controller for a compatible locating sensing cable, with RS485 and relay outputs. The XW-PC-3 reference lists a monitored run up…
LCP-000121
A complete modular water-sensing cable with factory-installed plastic connectors. The Raychem TT1000 series is documented for data-center subfloors and pipe-adjacent leak detection…
LCP-000005
A separately housed leak-detection panel that monitors sensing-cable circuits and provides alarm outputs; the pictured device is an exact model reference, not…
LCP-000095
A stand-alone optical point leak sensor with one configurable dry-contact output. The documented XW-DC-01B uses DC 9–30 V and a normally open…
Specify with confidence
Point or cable detection and intended coverage Fluid to detect and installation environment Alarm/output interface and power supply Mounting, replaceability and verification requirements Quantity and buyer-owned control-system interface
Leak-detection components can watch a local point or an extended cable path. Sensor placement, fluid sensitivity and alarm interface define the useful coverage.
Describe the protected area, fluid, environment, electrical output, power and mounting. Set the verification procedure and keep control-system alarm logic within the buyer-defined integration scope.
Include the drawing or specification revision and identify any requirements that are still to be confirmed. Available configurations, testing and documentation are confirmed with quotation.
Local editorial preview
Manufacturer examples retain their model and conditions. These references describe source products, not approved stock or supply. Images are pending final selection and rights review.
| Parameter | Documented value / configuration |
|---|---|
| Detection method | Conductive liquid sensing cable with locating or non-locating alarm-unit options. |
| Fluid | water; conductive base liquids |
| Installation | Pre-connected 3 m, 7 m, and 15 m cable lengths; locating use requires compatible addressable interface/alarm unit. |
| Parameter | Documented value / configuration |
|---|---|
| Coverage | location accuracy m: 1; maximum per circuit m: 600; maximum total m: 1800 |
| Output | eight programmable alarm relays; power-fail relay; Modbus over RS232/RS422/RS485 |
| Power | 100–240 VAC, 50/60 Hz, 15 W |
| Parameter | Documented value / configuration |
|---|---|
| Model identity | MA1YHZ0102(1.0) water leakage detection cable |
| Detection method | Conductive-liquid detection through internal conductors |
| Operating temperature | -40 to 70 °C |
| Construction | Braided dust-resistant outer layer around conductive inner wires |
| Service feature | Reusable after drying, subject to the matched detection system |
| Parameter | Documented value / configuration |
|---|---|
| Model identity | XW-ES2-10H1 locating leak detection cable |
| Cable diameter | 6.0 mm |
| Cable resistance | 13 ohm/m |
| Operating temperature | -20 to 75 °C |
| Construction | Four conductors; two conductive fluoropolymer-covered sensing wires around a helical core |
| System interface | Used with a compatible Xiangwei locating leak controller for position reporting |
| Documented detection coverage | Liquid contact can be detected along any position of the sensing cable when connected to a compatible Xiangwei locating leak controller; the maker's tap-water alarm criterion is at least 30 mm wetted cable lengthConditions: scope: Manufacturer's tap-water reference condition only; detection of a different coolant, conductivity, cable route or controller combination requires its own test |
| Parameter | Documented value / configuration |
|---|---|
| Model identity | XW-DC-01A photoelectric and electrode spot leakage sensor |
| Detection method | Photoelectric plus electrode detection for conductive/non-conductive liquid distinction |
| Supply voltage | DC 9–30 V; 12 V recommended |
| Signal interface | RS485; MODBUS-RTU |
| Operating temperature | -40 to 70 °C |
| Protection level | IP66 as listed by maker |
| Parameter | Documented value / configuration |
|---|---|
| Model identity | XW-DC-01B photoelectric spot leakage sensor |
| Detection method | Optical leakage detection |
| Supply voltage | DC 9–30 V; 12 V recommended |
| Signal interface | One dry-contact relay; normally open or normally closed |
| Operating temperature | -40 to 70 °C |
| Relay load | 125 VAC / 0.5 A or 30 VDC / 1 A |
| Parameter | Documented value / configuration |
|---|---|
| Model identity | XW-PC-3 locating leak detection controller |
| Monitored cable length | Up to 150 m with matching locating sensing cable |
| Supply voltage | DC 9–30 V; 12 V recommended |
| Signal interface | RS485 plus one dry-contact relay (NO/NC) |
| Response time | ≤8 s under maker's stated test context |
| Operating temperature | -40 to 70 °C |
| Parameter | Documented value / configuration |
|---|---|
| Product identity | TT1000 modular water sensing cable with factory-installed plastic connectors |
| Detection method | Conductive-polymer cable detects water along its length when used with a compatible alarm and locating module |
| Application scope | Data-center subfloors, mechanical rooms, pipes and other flat-surface leak-detection areas |
| Cable construction | Two sensing wires, one alarm signal wire and one continuity wire embedded in a fluoropolymer carrier rod |
| Cable diameter | 6.0 mm nominal |
| Available modular lengths | 1, 3, 5, 7, 15, 30 and 50 m catalog versions with factory-installed connectors |
| Maximum continuous operating temperature | 75 °C (167 °F) |
Selection resources
Selection guide
Define interface, service method, fluid conditions, materials, validation, and quantity before comparing coupling options.
Read guideSelection guide
Separate the service architecture from the exact connector interface before preparing an RFQ.
Read guide
Selection guide
A practical checklist for routed liquid-cooling assemblies.
Read guide